What Does a 5.5 m Car Turntable Require Beneath the Floor?

The 420 mm height is only one part of a 5.5 m car turntable installation. Check the recess, floor tolerances, drainage, drive access and vehicle approach.

Car turntable structure during installation

A 5.5 m car turntable is large enough to rotate a complete passenger car without reversing, but the visible deck is only part of the installation. If the platform must finish level with the driveway, the recess, base, drainage, drive clearances and access openings beneath it all have to be planned together. The turntable cannot simply be dropped into a circular hole after the paving is finished.

Car turntable structure during installation
The supporting frame, drive and floor interface must be set out before the finished surface is closed.

What does a 5.5 m car turntable need beneath the floor?

It needs a structurally suitable recess that receives and supports the turntable, keeps the operating mechanism clear, separates the rotating deck from the surrounding paving and allows water and services to be managed. The 420 mm finished height of the TT2555 is one key dimension, but it is not a complete foundation specification by itself.

The project also has to account for a 2.5 t vehicle load, a 5.5 m rotating deck, a pin-gear drive with an RV63 reducer and Harbin bearings. How those loads reach the slab and how the pit is drained and serviced depend on the building. Use the approved drawing rather than assuming a standard excavation depth.

Which dimensions define the opening?

The nominal turntable diameter is 5.5 m, but the construction opening is more than a circle of the same size. There must be a defined gap around the rotating assembly so the deck does not rub against the paving, retaining edge or drainage cover. The edge detail also has to prevent loose aggregate and debris from falling into the drive area.

Set out the opening from the approved drawing, including the frame or support points, service access and the position of the entry and exit edges. Check the full rotation before the concrete or paving is completed. A deck that is accurate only in the parked position can still foul a kerb, wall or threshold as it turns.

The TT2555 case calls for floor flatness and turntable roundness within plus or minus 10 mm. Those tolerances should be translated into a practical inspection method and hold points before the slab and finished surface are closed. Measuring only the visible circumference is not enough if the base and moving ring are not on the intended planes.

How should the floor carry the load?

The supporting structure needs to transfer the vehicle load and the turntable’s own load into the building or ground without settlement or rocking. The slab design, reinforcement, joints and connection to the surrounding pavement are site-specific. The finished topping should not bridge over a soft or moving layer that can compress under the wheel path.

Confirm how vehicles will approach the turntable. A wheel crossing a lift edge can apply a concentrated load to a small area, particularly if the car enters at an angle. The approach structure should provide a continuous bearing path and avoid an abrupt step at the rim. Final member sizes and concrete details must come from the structural design, not from the deck dimensions alone.

What has to remain accessible around the drive?

The pin-gear drive and RV63 reducer need a clean operating zone and enough access for inspection. A recess that leaves no room to inspect the drive, bearings or fasteners saves nothing if every service visit requires the finished floor to be opened.

Keep the cable route and control connection inside protected ducts or service channels. They must not become a drain for surface water or a trip hazard at the deck edge. Confirm the supply and control arrangement before casting the slab, because adding a cable opening after paving can weaken the edge detail and disturb the finished surface.

How should water and debris be managed?

An open recess can collect rainwater, cleaning water, grit and leaves. The drainage method must remove water without allowing it to rise into the mechanism, and the edge gap must not become a path for stones that can jam the drive. The final arrangement should be coordinated with the waterproofing, paving falls and local drainage system.

How does 420 mm compare with other turntable installations?

Height and drive design change with the size and duty of the platform. The following comparison uses three real project configurations to show why a single generic pit detail cannot be copied from one turntable to another.

Project reference TT2555 TT6-6 TT3016
Market Namibia Tanzania Bangladesh
Diameter / deck 5.5 m 6 m 16 m; deck 12 – 16 m
Height or interface 420 mm finished height 500 mm thickness Flush with floor; pit frame 300 x 100 mm
Capacity 2.5 t 6 t 30 t
Drive detail Pin gear, RV63 reducer 380 – 400 V three phase Slewing bearing, 2.0 kW
Rotation speed 1 – 2 rpm Not stated 1 – 2 rpm
Car turntable platform and drive ring
The drive ring and reducer must be accessible without disturbing the finished floor.

Recessed or surface mounted: what changes?

A recessed installation gives a level driveway, but it concentrates more work into the base, drainage and edge construction. A surface-mounted turntable avoids the large floor opening, but it needs a safe approach on every side and may alter ramp length, headroom or kerb geometry. Neither arrangement removes the need to check vehicle clearance and the structural load path.

For the TT2555, the 420 mm height and 5.5 m diameter should be shown on the same drawing as the surrounding pavement. An above-floor version would also need a deliberate transition so wheels do not strike the deck edge.

What should be inspected before the floor is closed?

  • Turntable position, diameter and full rotation clearance.
  • Base support, slab level, flatness and roundness measured against the approved tolerances.
  • Space for the pin gear, RV63 reducer, bearings, fasteners and service covers.
  • Drainage falls, waterproofing and protection against debris entry.
  • Cable route, control position and isolation from surface water.
  • Vehicle approach on all sides, including the transition at the deck edge.
  • A complete trial rotation and inspection before handover.

For the Namibia project, the TT2555 was configured at 5.5 m diameter, 420 mm height and 2.5 t capacity, with 1 to 2 rpm rotation, a pin-gear drive, RV63 reducer, Harbin bearings and a flatness and roundness requirement of plus or minus 10 mm. Those figures show the level of detail needed; the foundation package still has to be resolved for the actual slab and vehicle approach.

Car turntable installed flush with the floor
A flush deck needs a continuous support edge, controlled tolerances and clean drainage.

Frequently asked questions

What foundation depth does a 5.5 m car turntable need?

There is no single depth that applies to every site. The 420 mm finished height describes the TT2555 assembly, while the recess, base and structural design depend on the building, slab and approved installation drawing. A contractor should not excavate from the height figure alone.

Can a car turntable be installed without a recess?

Yes, an above-floor arrangement can avoid a large opening, but it creates a raised edge that must be handled safely. The approach needs enough clearance for the underside and wheels of the vehicle, and the installation drawing must show how the platform meets the surrounding surface.

Why is floor flatness important for the TT2555?

The specified project tolerance was plus or minus 10 mm for floor flatness and turntable roundness. Uneven support or a poor circular edge can affect rotation clearance and cause rubbing. The measurement and inspection method should be agreed before the floor finish is completed.

Next step

Send the finished floor levels, a plan of the opening, the vehicle dimensions, photographs of the approach and any structural drawings. Start with the car turntable range, and read how a 30 t, 16 m vehicle turntable is specified when the vehicle or opening is larger.

Share:

More Posts

Send Us A Message

Scroll to Top